$549.95 FOR THE PAIR

HERES A LINK: UTV Crap

RAW STEEL TUBE FRAME AND RAW ALUMINUM SKIN

__________________

Nice! What kind of mounting hardware? Can these be used with the countersunk XMF bungs?

__________________

Pretty nice, I might go this route, but need some scratch first!

__________________
All AMSOIL Fluids, Rigid RAD4 Cage, BS Sand Seats, Dirt Light HID, UTV Crap, Checker 4" HID, Dynatec CDI, Hunterworks Carb Kit, DJ Safety Belts, JP Cooler, Axia Alloy Exhaust Tip, Fuel Gauge, Quick Light 6" Fiber Whip (red), Trail Logic Skids, Rugged Intercom, Monster Edition Rims, Maxxis Cerros
www.az-lube.com
az_amsoil@cox.net

Its Comes With What You Need To Mount, They Use The Factory Bungs Or The Counter Sunk Style.

__________________

Are those 1/2 3/4 or fullsize doors

Bolt On Teryx Full Doors - Utv Crap

__________________

I know it might be a little work but can you bolt one up or just mock it up so we can see the fit. (picture). I need doors before Thanksgiving and these might just do the trick if they fit up well.
Couple questions:
1. How is the gas cap hole / cover built on these. I don't see any hole on the right side door ( silver / metal one)
2. Do they have any bow out at the top to accommodate for wider seats and the lowering bases
3. Are they Zuse fasteners or bolts and nuts holding the skins on
4. what dia. is the tubing used
5. Couple pictures from the side front angle and back angle of both sides would be great.( on the Teryx) Also the inside of the door.
6. From the picture the mount hole look about 1/2" thick. Do they come with new bolts? As it is now I wouldn't think the stock ones would fit correctly

Thanks for your time.
Again I only ask this stuff because I really need doors and from just the one picture Its hard to tell
John

__________________
2008 Teryx
So Cal Fab +5 Arms w/ Sway-A-Ways, Summers Brothers Axles, So Cal Fab 4 place Cage with roof, Beadlock Spec. Spyders with 9" BigHorns, PRP Low Backs w/ Crow Belts, Optimum Battery, Lawrence 540c Baja GPS, CDI by VDI, Radiator Shrouds, Billet Tip on Pipe, Wink Mirror, Billet Grab handels, 4 H.I.Ds across the top on So Cal Fab folding Light Bar, Trail Tech Vapor Digi Dash, Front & Rear Bumpers, SafeGlow LED whip, Momo Trek Wheel, 3/4 doors.

john,

give me a little bit and ill get some pictures for you.

__________________

I'd definately like to see those too. Nice looking so far fo sho!

They look nice ,but I can't make out where they hinge from and what does the top section look like. I assume by saying full doors there is a top half.

I doubt they hinge cliff. They are to bolt on and stay on. You gotta lift a leg over 'em

You see the whole door there - they'd be the height of the cage bung...

Well then, let's not call them FULL doors .Where I come from doors have hinges, catches and latches. Let's call them half panels. They would be great for the racer types ,but I don't know too many hunters or trail riders that would be comfortable with these panels. I'm not trying to be a smart ass but I am in the market for full doors with hinges because my wife is not going to like entering the machine like Daisy Duke and when I'm plowing snow gettingin and out will be a pain in the shins

These are full doors. The flimsy little thing Yamaha puts on their Rhino is a half door. So let's call them what the market calls them...

Any type of panel that bolts onto a UTV like these is commonly referred to as a door.


Good question about the gas filler hole!

__________________

I really think you guys all need doors

__________________